Skip to content
  • Deszkowice Drugie 146, 22-448 SułówDeszkowice Drugie 146
  • Mon–Fri 8:00–16:00

P27F500 Fault – DSG Gear Selector Repair and Reconditioning (VW, Skoda, Audi, Seat, Cupra)

P27F500 is a code stored by the DSG gearbox control unit in Volkswagen Group cars on the MQB Evo platform with an electronic shift-by-wire gear selector (module 5WA 713 033): VW Golf VIII and Caddy V, Skoda Octavia IV, Audi A3 8Y, Seat Leon IV, Cupra Leon and Formentor, from 2020 onwards. In SAE wording it reads "Gear Shift Lock Solenoid/Actuator A – Stuck Off"; VAG testers show it as "Magnet 1 for selector lever lock – stuck open". It means the solenoid that locks the selector in P does not confirm that it has closed. The fault sits in the selector module in the centre console, not inside the DSG gearbox. The dashboard shows a yellow gearbox symbol and the message "Error: gear selector. You can continue driving". We recondition the selector lock module – the car gets its original module back, with no need to replace the whole selector.

A dealer workshop usually proposes a complete new selector module with coding. We repair the lock mechanism itself. The repair is done on the car in our workshop or by post – you send us the removed module and we return it reconditioned.

Photos from the DSG gear selector repair – Skoda Octavia IV

What is the electronic DSG gear selector (module 5WA 713 033)?

With the MQB Evo platform – that is, from the 2020 Golf VIII and Octavia IV – Volkswagen Group cars with DSG got an electronic shift-by-wire gear selector. The classic lever linked to the gearbox by a cable gave way to a small toggle in the console: nudging it towards R, N or D/S is only an electrical signal to the gearbox control unit, and P is engaged by a separate button. The only mechanical link to the toggle is the emergency parking lock release cable – the one visible in the photos next to the module harness.

The whole mechanism – toggle, position sensors, P button, lock solenoid and emergency cable – forms a single module with part number 5WA 713 033 and a suffix that depends on the model and model year (in the 2021 Octavia IV we repaired: 5WA 713 033 AN). The lock solenoid, marked 100.125.196-04, sits in the module socket on spring contacts and holds the selector in P until the driver switches the ignition on and presses the brake. The gearbox control unit supervises its circuit by measuring the voltage drop every time it operates.

That supervision is exactly where code P27F500 comes from. When the solenoid does not close, closes late, or a poor contact in the socket stops the control unit from seeing the voltage drop, it stores a lock fault and displays the message on the dashboard. The DSG gearbox – whether a DQ200, DQ381 or the DQ400e in the hybrids – keeps working normally, because the problem is in the console, not in the mechatronic unit. This is a completely different situation from the faults described on the DQ250 DSG gearbox page, where the codes concern clutches and solenoid valves.

  • Shift-by-wire – no gear selection cable – the small toggle in the console has no mechanical link to the gearbox – it sends an electrical signal to the DSG control unit; the only cable in the module is the emergency parking lock release cable, which the lock solenoid holds in the P position
  • Selector lock solenoid – holds the selector in P until you switch the ignition on and press the brake; the control unit monitors its circuit by measuring the voltage drop – when no drop is seen and the lock does not confirm closing, it stores code P27F500
  • Module 5WA 713 033 with many suffixes – the same module comes with suffixes that depend on the model and model year – AN, BB, BS, BT, CD and CE among others; in the Octavia IV we repaired it was 5WA 713 033 AN, and the lock solenoid carried the marking 100.125.196-04
  • Message and symbol on the dashboard – a yellow gear wheel with an exclamation mark and the text "Error: gear selector. You can continue driving" – in more severe cases the car also asks you to secure it with the parking brake
  • It is not a DSG gearbox fault – the code is stored by the gearbox control unit, but it concerns the module in the console; the gearbox itself (DQ200, DQ381, DQ400e) needs no repair in this case – an oil change or clutch adaptation changes nothing here
  • Sporadic and temperature-dependent – the code often appears when cold, after a long stop or with a weak battery, disappears for a few days and comes back; that is why we check the occurrence counter and the power supply before removing anything

Supported models with shift-by-wire selector

Volkswagen / Skoda

  • VW Golf VIII (CD1) – from 2020, including the GTI, GTE, R and Estate with DSG
  • VW Caddy V (SB) – from 2020, DSG versions
  • VW Tiguan II facelift (AD1) – from 2020, selected versions with the electronic selector
  • Skoda Octavia IV (NX) – from 2020, including the Octavia vRS and the iV hybrid

Audi / Seat / Cupra

  • Audi A3 8Y – from 2020, Sportback and Saloon with S tronic
  • Seat Leon IV (KL) – from 2020, including the e-Hybrid
  • Cupra Leon – from 2020, including the e-Hybrid
  • Cupra Formentor (KM) – from 2020, DSG versions

Most common causes of the DSG gear selector fault

In practice code P27F500 has four sources – from a genuine fault of the lock mechanism, through the contacts in the socket, to the power supply and software. The order of checking matters, because removing the module with a weak battery is a waste of time and money:

Lock solenoid does not close (P27F500)

The most common scenario. The selector lock solenoid stays open or closes late, so the control unit sees no confirmation of closing and stores P27F500. The mechanism can be reconditioned without replacing the whole selector module.

  • "Error: gear selector. You can continue driving" message
  • Yellow gearbox symbol on the dashboard
  • Code P27F500 returns after being cleared
Solenoid contacts in the module socket

The solenoid sits in the module socket on spring contacts. Too little contact pressure gives an open circuit that the control unit cannot tell apart from an open lock. Typical sign: the fault appears on rough roads or after a tap on the console next to the selector.

  • Fault appears on bumps or when the console is tapped
  • Static or sporadic fault, temperature-dependent
  • No mechanical symptoms at the selector itself
12 V supply and earth

A weak or flat battery and an unstable on-board voltage can trigger the same message with no module fault at all. So before we remove anything we check the cranking voltage, the earths and the battery condition – especially on plug-in hybrids, where the 12 V battery is often neglected.

  • Fault after a cold night or a long stop
  • Car does not start at the first attempt
  • Code disappears after charging the battery and returns a week later
Control unit software

For some model years the manufacturer issued software updates because the message appeared without a physical fault. An update will not, however, fix a solenoid that genuinely sticks in its socket – if the occurrence counter rises with every driving cycle, the fault is current and mechanical.

  • Code with no symptoms at the selector
  • Car from the first MQB Evo model years (2020–2021)
  • Occurrence counter does not rise after the update

P27F500 fault – what exactly it means

Code P27F500 is, in SAE wording, Gear Shift Lock Solenoid/Actuator "A" – Stuck Off, and in VAG dealer testers: Magnet 1 for selector lever lock – stuck open. Cheap OBD readers show it in the short form P27F5. The code is stored by the gearbox control unit (address 02 – Transmission Electronics), because that is what powers and supervises the lock solenoid – even though the component itself sits in the selector module in the console.

The way the code is set is simple: every time the solenoid operates, the control unit expects a voltage drop in its circuit. If there is no drop and the lock does not confirm closing, the fault goes into memory – first with passive/sporadic status (as in the Octavia IV we repaired), and, when it repeats over successive cycles, as a static fault. The message "Error: gear selector. You can continue driving" does not restrict driving, but warns that the parking lock in the P position may not be confirmed.

In the cars we repair, P27F500 occurs on its own – without clutch, pressure or position sensor codes. If you see other gearbox codes next to it, that is a separate problem, which we diagnose separately; the lock code itself is not a sign of DSG wear and requires neither an oil change nor a gearbox adaptation.

DSG gear selector fault codes

For the selector lock module the gearbox control unit stores, in practice, a single code – only its notation differs from tester to tester:

Selector lock fault code

Fault codeDescription and cause
P27F500Gear Shift Lock Solenoid/Actuator "A" – Stuck Off; in VAG testers: Magnet 1 for selector lever lock – stuck open. Stored in the gearbox control unit (address 02 – Transmission Electronics) when the lock solenoid circuit shows no voltage drop and the lock does not confirm closing. Passive/sporadic status means a recurring fault; static means it is present at the time of the readout.
P27F5The same code in the generic five-character form – this is how cheap OBD readers display it. The last two characters "00" in the VAG form are the fault type. Whatever the notation, the code concerns the lock solenoid in the selector module, not the mechatronic unit or the DSG clutches.

Symptoms of a DSG gear selector fault

The symptoms are discreet – the car drives normally and the problem shows mainly on the dashboard. If you have an older car with a classic lever that will not release at all with the brake pressed, that is a different system – see the guide gear lever stuck with the brake pressed.

Scope of our DSG gear selector repair

We repair the lock mechanism itself rather than replace the module. The scope is the same on the car and by post – the only difference is who removes and refits the module in the console:

1. Initial diagnosis

We establish whether the code is current and whether its source is the module rather than the power supply – without removing anything:

  • Readout of the code directly from the gearbox control unit (address 02) with its status and occurrence counter
  • Check of the cranking voltage, battery condition and earths
  • Lock test: locking and releasing the selector cold and with the cabin warmed up
  • Readout of the selector module number (5WA 713 033 + suffix) for the quote

2. Module removal and lock reconditioning

The selector module sits under the centre console trim and comes out as one unit:

  • Removal of the console trim with a trim tool – no scratches on the gloss plastic
  • Disconnection of the harness and of the emergency parking lock release cable
  • Removal of module 5WA 713 033 and of the lock solenoid from its socket
  • Reconditioning of the selector lock mechanism
  • Bench test of the solenoid before refitting

3. Refitting, test and code clearing

The car gets its original module back, so there is no new part to order and nothing to wait for:

  • Refitting of the module, connection of the harness and emergency cable, refitting of the trim
  • Test of the P lock and of the brake release with the ignition on
  • Clearing of code P27F500 and a check that it does not return after several ignition cycles
  • Road test with P–R–N–D–S changes

Gear selector module repair by post

The 5WA 713 033 selector module comes out of the console as one unit, so we also carry out the reconditioning by post: the customer or their workshop removes the module, packs it and sends it by courier, and we recondition the lock mechanism, test the solenoid and send the module back. With this option, removal and refitting in the car are the customer's responsibility – we are not responsible for those steps, we are responsible for the reconditioned module.

If you prefer to drive in, our workshop in Deszkowice Drugie carries out the full service: diagnosis with a power supply check, removal of the console trim and the module, lock reconditioning, refitting, code clearing and a road test. We accept mechatronic units and control units of other gearboxes by post in the same way – see the list of supported controllers.

Why us?

  • Reconditioning instead of a new module – we repair the lock mechanism rather than replace the whole selector – a fraction of the price of a new part with coding
  • The original module goes back into the car – the same unit, the same part number – no part to order, no waiting for delivery
  • Repair by post – send the removed module by courier from anywhere in Poland and we return it reconditioned
  • Power supply first, removal second – we check the battery and the voltage before taking anything apart – a weak 12 V supply gives an identical message
  • Experience with DSG gearboxes – we repair DSG mechatronic units, clutches and control units – we know when a code concerns the module in the console and when it concerns the gearbox
  • Warranty on the repair – the reconditioned lock mechanism is covered by a warranty on the work carried out

How the service works

  1. Contact and description of the symptoms – model, model year, the wording of the message and – if you have it – the code read out
  2. Diagnosis on the car – readout of the code and occurrence counter from the gearbox control unit, power supply check
  3. Selector module removal – console trim off, harness and emergency cable disconnected, module out
  4. Lock mechanism reconditioning – repair of the lock solenoid and bench test
  5. Refitting and test – original module refitted, P lock tested, code cleared
  6. Car collection or module return – road test in the workshop, or return shipment for a repair by post

Pricing

ServiceDescriptionTurnaround time
DSG gear selector diagnosisCode readout from the gearbox control unit, power supply check, lock testFree with the repair
Selector lock module reconditioning – on the carModule removal, lock mechanism reconditioning, refitting, test, code clearingIndividual quote
Selector lock module reconditioning – by postYou send the removed 5WA 713 033 module, we return it reconditionedIndividual quote
Code clearing and test after the repairCheck that P27F500 does not return after several ignition cyclesIncluded in the repair

* Quoted after the diagnosis – it depends on the model, the condition of the lock mechanism and whether the repair is done on the car or by post. The reconditioning price is a fraction of the cost of a new selector module with coding.

Get in touch

Does your car show "Error: gear selector. You can continue driving" with P27F500 in the control unit? Contact us – we will check the power supply, read the occurrence counter and recondition the selector lock module without replacing the whole selector. On the car or by post.

We also repair other gearboxes

Frequently asked questions


What does code P27F500 mean on a VW, Skoda, Audi, Seat or Cupra?

Code P27F500 (generic form P27F5, "Gear Shift Lock Solenoid/Actuator A – Stuck Off") is stored by the DSG gearbox control unit in Volkswagen Group cars with an electronic shift-by-wire gear selector, built from 2020 on the MQB Evo platform. It means the selector lock solenoid stays in the open position or does not confirm closing – the control unit does not see the expected voltage drop in its circuit. The fault concerns the selector module in the centre console (part number 5WA 713 033 with a suffix), not the DSG gearbox. It comes with the message "Error: gear selector. You can continue driving" and a yellow gearbox symbol.

Does P27F500 mean the whole gear selector has to be replaced?

No. A dealer workshop replaces the complete 5WA 713 033 selector module with coding as standard, but the source of code P27F500 is usually the lock solenoid itself and the way it sits in the module socket. This mechanism can be reconditioned – the car gets its original module back, the same unit and the same part number. The cost is a fraction of the price of a new selector, and the repair can be done on the car in our workshop or by post, by sending just the removed module.

Can I keep driving with the "Error: gear selector. You can continue driving" message?

The message itself says that you can continue driving – the DSG gearbox works normally and code P27F500 does not put it into limp mode. The risk concerns parking: the selector lock in the P position does not confirm closing, so in the more severe variant of the message the car asks you to secure it with the parking brake. Until the repair it is worth parking with the parking brake applied and not forcing the selector when it refuses to leave P – just wait a moment with the brake pressed and the ignition on.

Which cars are affected by the P27F500 fault?

Volkswagen Group cars on the MQB Evo platform with an electronic shift-by-wire selector and a DSG gearbox, built from 2020: the VW Golf VIII (including the GTI, GTE and R), VW Caddy V, selected versions of the facelifted VW Tiguan II, Skoda Octavia IV (including the vRS and the iV hybrid), Audi A3 8Y, Seat Leon IV, Cupra Leon and Cupra Formentor. All of them use the same 5WA 713 033 selector module family, differing only in the part number suffix according to model and model year.

Is P27F500 a DSG gearbox fault?

No. The code is stored by the gearbox control unit because it supervises the lock solenoid circuit, but the fault concerns the selector module in the centre console. The dual-clutch gearbox itself – a DQ200, DQ381 or the DQ400e in the hybrids – needs no repair in this case. A DSG oil change, clutch adaptation or a mechatronic unit rebuild changes nothing here. The reverse also applies: if you see clutch or pressure codes next to P27F500, that is a separate problem, which we diagnose separately.

Can I send just the selector module for reconditioning?

Yes. We accept removed 5WA 713 033 selector modules by courier from all over Poland. With a repair by post, removal and refitting of the module in the car are the responsibility of the customer or their workshop – we are responsible for reconditioning the lock mechanism and testing the module before returning it. If you prefer to drive in, we carry out the full service in the workshop: diagnosis, removal, reconditioning, refitting, code clearing and a road test.

Why does code P27F500 come back after being cleared?

Because clearing removes only the entry in the control unit memory, not the cause. A lock solenoid that sticks in its socket or has too little contact pressure will again fail to confirm closing on the next ignition cycle – and the code returns. The occurrence counter in the gearbox control unit helps: if it rises with every driving cycle, the fault is current. Before ordering a module repair, however, it is worth ruling out a weak battery and an unstable 12 V supply, which give an identical message.

Can a weak battery cause the gear selector error?

Yes. A low or unstable 12 V voltage during cranking can trigger the "Error: gear selector" message and code P27F500 with no module fault at all – the lock solenoid simply does not get its full supply. This applies above all to cars that stand for long periods and to plug-in hybrids, where the 12 V battery is often neglected. That is why we start the diagnosis with a voltage measurement and an earth check; we remove the module only when the supply is in order and the occurrence counter is rising.

How do I check which selector module my car has?

The part number is on the module label, visible once the console trim is off – it starts with 5WA 713 033, followed by a letter suffix (e.g. AN, BB, BS, BT, CD, CE) that depends on the model and model year. In the 2021 Octavia IV we repaired it was 5WA 713 033 AN, and the lock solenoid carried the marking 100.125.196-04. For a quote, though, the model, model year and the wording of the message are enough – we read the module number ourselves during the diagnosis.

Call